Update
Applications
Advantages:
For developer:
(Пайпы программ) Companies:
History:
(Бонусы) Advice:
(Барьеры и решения) Technologies:
(Применение в науке, лаборатории, ..)
Solutions
New eComStation:
Future:
(Ссылки на другие сайты) (Картинка дня) OS/2 artefacts:
Gadgets:
|
LG U8130
Mark: Good In VOICE newsletter june 2006 Ed Durrant wrote an article on
connecting his eCS computer to internet via an LG 8330 cell phone. The
article is here.
Well I decided to try it out on my LG U8130 and it turned out to work.
Instead of Injoy dialer (which Ed used) I tried eCSCoNet dialer coming
with eComStation. Read Eds article for a more comprehensive
walkthrough. Here's the steps I took:
Phone: No preparing needed for my part. You may need to download
"internet settings" from your phone network provider if you haven't
done before. My APN (access point name) says eg services.djuice.se .
eComStation:
- If you don't have it earlier - add a line loading usbcom.sys to
config.sys. In my case it says: DEVICE=C:\OS2\BOOT\USBCOM.SYS /N:COM4.
(Ed choosed COM8. That didn't work for me, eCSCoNet just shows 1-4.)
Be shure that usbcom.sys exists on you system, otherwise download from
ecomstation.com. Now reboot
- On desktop open up Internet>Dial-up tools. Start "Configure
eCSCoNet with internet assistant".
- Go through some "Next steps", then choose "Serial port (Modem or
virtual device)" and press NEXT. Call your connection something, eg
"LG". On phonenumber write 99 (*99# is required but eCSCoNet just
allows numbers). Choose "Automatic DNS.." and press NEXT
- Domain is required. I wrote djuice.se which is my providers
domain. Other fields will be filled automatically, just let them be
that and press NEXT
- Set COM port to whatever you choosed in "DEVICE" statement
above, in my case COM4. Set baudrate to highest, 115200. I can't get
it higher. Press NEXT
- Just press NEXT again and again (direct connection)and again.
There uncheck IBM dialer, it wont work (or it is harder to make it
work). Press NEXT
- You have to fill in "Full name" and "User name". It's not needed
so you can write anything. I just wrote "x" and "m". Press NEXT and
choose "Let dial in program prompt for password" Press NEXT. And press
NEXT again. And again.
- Now just check "Configure these values" and press NEXT. Program
gets configurated. Press NEXT again and then FINISH
Put your phone into USB and it will show up in USB-dock
(Programs>Utilities). Open eCSCONet and choose your connection name.
Press DIAL.
As you choosed "Let dial in program prompt for password" above it will
do that. And when it does you can add a "*" before "99" and a "#"
afterwords in the number. Do that and the press DIAL. In a moment
eCSCoNet will show your IP and you're up! (I noticed that if I
disconnect I have to reboot my phone to make it work again). My speed
was about 150 kb/s. I don't know if it is possible to get it higher if
one can set a higher baude rate in some way. Anyway it works very
well. Rates in Sweden is about 10 SEK (1 euro)/MB. So its ok to surf
around a bit and check mail and so on.
When there is time I will test this on other phones in my family and
try them out as well.
Diese Information wurde gesendet von: melf -- 2010-02-23 19:05:28
****************************************
[GoogleAdv]
Test the program:
|
PMView work on your computer during several years. It's time to reward the developer (+ send bug-reports and ideas to the developer).
|
Kommentare: melf 2008-09-12 19:26:24 | Hi guys, it is really ok that you cite this contribution from the os2world forum by me. I think it's very good to collect information about hardware as you do. But the information is not sent by me. Please just ask first! | Eugene Gorbunoff 2010-02-10 23:36:55 | ok! | Eugene Gorbunoff 2010-02-23 19:07:27 | Correction: this report was published before 2008/09 |
eCo Software is working with the translators
of eComStation / IBM OS/2 Warp since the end of 90-th.
We have released russian version of
some Fixpaks for Warp 4, eComStation 1.05, .. 2.1.
LANGE library, co-operation with european translators.
|
Ideas for the developers:
|
System information: drivers, resources, parameters.. Let's collect all functions aimed to collect system information in universal eSysInfo library
|
|
|
IBM OS/2 Warp
|
|